Submersible Well Pump Accessories. Torque Arrestors, Submersible Pump Cable, Well Seals, Bronze Pitless Adapters, Franklin Electric Pump Control Boxes, Sprinkler Timers, Strataflo Bronze Check Valves, Flo-Control PVC Check Valves, Pressure Switches, Liquid Filled Pressure Gauges, Wellmate Fiberglass Pre-charged Bladder Water Pressure Tanks, Pressure Relief Valves, and B/W Induction Liquid Level Controls

Franklin Electric Motor 4", 3 wire, single phase, 60 Hz, 1/2 HP to 5 HP,water cooled, submersible water well motors with 48" Leads and control boxes. Single phase three-wire submersible motors require the use of control boxes. Ships next business day

Franklin Monodrive variable speed constant pressure controllers are designed to provide constant pressure for single-phase, three-wire submersible water well pump systems. You can have constant pressure just by replacing the three-wire control box in a conventional system.

PumpTec Automatic Protection Control For Franklin Submersible Motors, Single-phase, solid state, load monitoring devices designed specifically for Franklin submersible motors to protect from running dry. They protects the life of 4" submersible pump and reduces the odds of ever having to see the motor again

Torque arrestors are clamped on the submersible well pump drop pipe and are field adjusted to hold the pump centered in the well casing. Fits 4"-8" well casings and 1 or 1-1/4 drop pipe.

Submersible pump cable 12/4 (3-wire plus ground) UL listed 3 wire copper cable (with ground) for use within the well casing supplying power to the submersible pump.

These 4 wire, black, heavy wall heat shrink splicing kits can be shrunk over a large diameter connector and still effectively seals watertight to a small diameter cable. Four butt connenctors are included.Slip shrink tube on each wire, crimp connector on each wire, center tubing over connector and heat from center outward, splice is complete when sealant flows fron end of tube. Do not overheat

The tape method was the only way to make a good splice until shrink tube splice kits became available. Many installers still use tape because it has worked for them for years. You crimp the conductors together, wrap each conductor with a layer of rubber tape followed with a layer of plastic electrical tape. This makes a watertight connection and insulates the conductors from each other and the well casing. Properly done, this technique makes an excellent splice, but is very time consuming.

Cast iron well seal with rubber packing gland for submersible and jet pumps. Prevents contamination from surface drainage. Easy to install, just fit in casing and tighten bolts. Corrosion resistant zinc plated steel bolts. Painted finish. Split top

Bronze pitless adapters to insure long life and durability in the most aggressive well conditions. External installation nipple makes installation easy.Rubber inner & outer casing gaskets for certified & approved water tight seal from ground water contamination.

Intermatic 24 Hour Electric Sprinkler Timer. Rainproof enclosure with provision for rain sensor. Built-in pump start relay. On-off switch allows for shutdown during rainy days. 14 day skipper wheel permits watering to be omitted on selective days.

Strataflo bronze spring loaded check valve. For cold water service to retain liquid in a system preventing loss of prime when liquid source is lower than pump. It prevents backflow by allowing liquid to flow in one direction only.

The pressure switch starts and stops the pump motor automatically at a predetermined pressure. A tube connects the switch to some point in the system on the discharge side of the pump. The pressure in the system then acts directly on a diaphragm in the switch, which in turn actuates the contacts in the switch.

High quality 2-1/2" stainless steel liquid filled pressure gauges with built-in snubber dampen the effects of pulsation and vibration, while perpetually lubricating the movement which will extend its life.

WellMate fiberglass bladder water pressure tanks are quicker, easier and less costly to install than steel tanks. They contain no steel, so there is no paint to scratch or touch-up and they cannot rust. All component materials are NSF and/or FDA listed.

Pressure relief valve 1/2" heavy duty bronze pressure relief valve for shallow, deep well and submersible pumps. Recommended only for cold water system installation. Spring loaded and pre-set at 100 PSI (Not adjustable). Not for use with hot water heaters.

The B/W/ floatless induction type liquid level control system provides automatic low level cutoff protection for Submersible Well Pumps.