Your First Choice for Pumps and Pump Systems
Call Icon Call (305)-754-0677 M-F 8am - 4pm EST | Contact | FAQ

Flojet Diaphragm Demand Pump 2 GPM 115V 60 PSI # D3835B5011A

Item#: FJC-PMP-D3835B5011A
Product Available Availability:Usually ships the next business day
Flojet Diaphragm Demand Pump 2 GPM 115V 60 PSI # D3835B5011A (DD) <br>
Reg. $320.68
Sale: $199.88

Flojet Self Priming Automatic Demand Water Pump self priming, double diaphragm Model # D3835B5011A Spec. # MPU 115V B/B 2C SW60. The built-in pressure switch will start and stop the pump when a discharge valve is opened and closed.

Suitability for the application should be determined by actual use and is the full responsibility of the buyer. No warranty, expressed or implied, can be extended by the equipment manufacturer where failure is caused by chemical attack on pump materials. Temperature, aeration, concentration, and other factors may change the effect of the specific fluid on the pump materials. Only pumps with Santoprene / EPDM elastomers are recommended for potable water. Units are NOT designed for permanent residential domestic water applications.

Do not assume chemical compatibility.
If the fluid is improperly matched to the pumps Elastomers,
the pump may fail to prime, leak, have low pressures
or the pressure switch may not shut off.

Specifications

Applications: Automatic water systems, liquid transfer, spraying, cooling, circulation, filtration and dispensing Wetted parts: Polypropylene housing, Buna N check valves and Buna N diaphragm. Duty Cycle: Intermittent. Can be run continuously for short periods of time. The higher the duty cycle the shorter the expected life of the pump Includes: Pump, Motor, 60 PSI pressure switch, 20132-000 motor mounting grommet kit. Inlet & outlet: 3/8" FNMT (Discharge port on left side looking at motor end bell) Electrical: Permanent magnet ball bearing type, TENV (non-ventilated) motor. 115 volts, single phase, 50/60 Hz., 0.6 amps maximum, 6' cord with plug Pressure switch setting: 60 PSI PSI Liquid temperature: 160 degree Fahrenheit maximum Priming capabilities: 8 feet dry prime, 15 feet when wet Dimensions: 4" high, 10" long, 4" wide. Weight: 4 lbs

NOTE: Use a minimum 40 mesh strainer in the pump inlet line to prevent debris from entering the system. Order separately

Pump Capacity Table D3835B5011A In Gallons Per Minute
Model Discharge Pressure (PSI) Shut-off
0 10 20 30 40 50
Gallons Per Minute (GPM)
D3835B5011A 2.0 1.4 1.2 1.1 0.9 0.3 60'

Questions & Answers

The Flojet manual states Intermittent duty. Can be run continuously for short periods of time. The higher the duty cycle the shorter the expected life of the pump.
Can be run continuously for short periods of time. The higher the duty cycle the shorter the expected life of the pump.
Up 60 minutes with discharge pressure of up to 20 PSI. Up to 20 minutes when the discharge pressure is over 20 PSI. The off-time should be the same or more than the run time.
Demand Operation is considered an "intermittent duty" application.
The maximum intermittent duty cycle is that which will cause the motor to reach its maximum thermal limits. Once the maximum thermal limit is reached, the motor must be allowed to settle to a lower temperature ideally being ambient before resuming operation. Running the pump at or near the maximum thermal limit for extended period of time will shorten the life of the pump and may result in immediate pump failure.
Only pumps with Santoprene / EPDM elastomers are recommended for potable water.
Units are NOT designed for permanent residential domestic water applications.

(?) Ask a question about Flojet Diaphragm Demand Pump 2 GPM 115V 60 PSI # D3835B5011A (DD)
Back to Top