Water System Accessories

American Granby

American Granby

American Granby was established in 1962. They provide water system accessories for the following markets: pump and well, pool and spa, sprinkler and irrigation and plumbing. The line includes leather cups and valves, well seals, well caps, pitless adapters, torque arrestors, pressure gauges, check valves, foot valves and pressure relief valves.

 Air Volume Controls

Brady air volume control model AV 42T, AV80T, AV100, AV120. Zinc die cast body, Buna N diaphragm and seal cap elastomers, brass spring and orifice; 100 PSI maximum pressure.

Brady Plastic Spring Loaded  Foot Valves / Check Valves

Brady plastic combination check valves and foot valves, prevent backflow and loss of prime while providing efficient flow. They consist of a line check valve, plus a strainer

 Pitless Well Adapters

Bronze pitless adapters to insure long life and durability in the most aggressive well conditions. External installation nipple makes installation easy.Rubber inner & outer casing gaskets for certified & approved water tight seal from ground water contamination.

Hand Pitcher Water Pump with Open Spout # HPP-10 (C)

Hand pitcher water pump with open spout # HPP-10. Pitcher hand water pump with open spout for cisterns and shallow wells up to 20 feet. Delivers approximately 1 GPM per 14 strokes. Tapped for 1-1/4" drop pipe. Easily installed. Corrosion resistant green primer paint finish. Cap adjustable for wide range of handle positions. Indent on spout for bucket handle.

Harvard Pressure Switch  30-50 PSI , 2 HP # CPS3050 (A)

Harvard pressure switch for water pumps 2 HP # CPS3050 30 PSI cut-in, 50 PSI cut-out; adjustable with maximum pressure setting of 60 PSI cut-in and 80 PSI cut-out; will handle single phase 1-1/2 HP @ 115 Volts and 2 HP @ 230 volts. It has 1/4 FNPT (Female pipe thread) bottom connection. Replaces Furnas pressure switch 69ES1. Ships the next business day.

Harvard Black Corrugated Flexible Hose 1-1/2" x 24' # SPDK150MHD (AA)<br>

The black color hose inhibits algae growth inside hose. Used only with submersible sump and effluent pumps. Kit contains 24' of flexible, corrugated poly-drain hose 1-1/2" I.D. hose; one 1-1/2 insert male adapter, one stainless steel clamps. Fits sump pumps with 1-1/2" female outlet.

Heat Shrink Cable Splicing Kits

These 4 wire, black, heavy wall heat shrink splicing kits can be shrunk over a large diameter connector and still effectively seals watertight to a small diameter cable. Four butt connectors are included.Slip shrink tube on each wire, crimp connector on each wire, center tubing over connector and heat from center outward, splice is complete when sealant flows fron end of tube. Do not overheat

Liquid Filled  Pressure & Vacuum Gauges  2"

Glycerine liquid filled 2" , 1/4" MNPT bottom connection, 2% accuracy, vacuum and pressure gauges with steel case and plastic lens for high vibration applications in 30 to 160 degrees Fahrenheit temperature.Use only with water

PVC Ball Valves

PVC Ball Valves 3/4", 1 ", 1-1/4", 1-1/2", 2", 3" and 4" PVC ball valves are constructed of quality materials using virgin schedule 80 PVC EPDM seats and seals. Rated 150 PSI at 72 degrees Fahrenheit water temperature. Full port flow opening, quarter turn operation. Fit schedule 40 and 80 pipes. Solvent ends comply with ASTM D2466. Materials meet NSF standards. Usually ships the next business day.

Pitcher Pump Leather Cup and Valve Kit  # LVC-2 (BB)

Pitcher Pump leather cup and valve for size 2 pump. Leather cup OD: 3", Cylinder ID: 3: Cup Hole Size ID: 2", Cup height: 13/16", Leather valve OD: 3-1/2" for 3" cylinder ID, Standard ID: 2-7/8"

Pressure Relief Valve 1/2" (Set 100 PSI) # IRV50-100NL (D)

Pressure relief valve 1/2" heavy duty, no lead, bronze pressure relief valve for shallow, deep well and submersible pumps. Recommended only for cold water system installation. Spring loaded and pre-set at 100 PSI (Not adjustable). Not for use with hot water heaters.

Well Caps

Cast Aluminum standard ventilated well cap with conduit opening. Standard 4". 5" and 6" cast aluminum well caps for use on steel or plastic casiing. Stainless steel set screws

Torque Arrestor TA-48

Torque arrestors are clamped on the submersible well pump drop pipe and are field adjusted to hold the pump centered in the well casing. Fits 4"-8" well casings and 1 or 1-1/4 drop pipe.

Teflon Tape For Pipe Threads

Teflon Tape for pipe threads. Standard density, 1/2" X 520" and 3/4" X 520", Teflon tapes for general purpose sealing in water pipe threads.

Well Seals

Cast iron well seal with rubber packing gland for submersible and jet pumps. Prevents contamination from surface drainage. Easy to install, just fit in casing and tighten bolts. Corrosion resistant zinc plated steel bolts. Painted finish. Split top

Pump Motor Cover

This universal pump motor cover is made of heavy duty plastic for long life and durability, It shields and protects outdoor motors from the sun, rain and dust. The heat resistant white top and attractive blue sides will not fade from sun or ultraviolet rays. It assembles in minutes without the need of any tools. Fits pool, spa and sprinkler pump motors from 1/3 to 2 HP. It will not fit jet pump motors that have a pressure switch mounted on the side of the motor. Dimensions: 13" long, 8 1/2" high and 8" wide

Questions & Answers

Ask a question about American Granby. Click here
Customer Reviews

About Us Contact Us Customer Reviews Facebook Twitter Disclaimers Privacy Policy Returns Shipping Policy Terms of Sale Terms of Use Warranty FAQ Site Map Technical Info Terminology Troubleshooting
  • Internet prices apply only to Internet purchases.
  • Minimum order amount is $20.00.
  • All merchandise listed is in stock.
  • Orders are shipped the next business day.
  • We only sell within the 48 adjacent United States.
  • Shipping tracking numbers are e-mailed automatically.
  • Office hours are: Mon - Fri, 8am - 4:30pm EST excl. holidays.
Copyright © 2012 All Rights Reserved.