 | These 4 wire, black, heavy wall heat shrink splicing kits can be shrunk over a large diameter connector and still effectively seals watertight to a small diameter cable. Four butt connectors are included.Slip shrink tube on each wire, crimp connector on each wire, center tubing over connector and heat from center outward, splice is complete when sealant flows fron end of tube. Do not overheat |
|
 | Torque arrestors are clamped on the submersible well pump drop pipe and are field adjusted to hold the pump centered in the well casing. Fits 4"-8" well casings and 1 or 1-1/4 drop pipe. |
|
 | Bronze pitless adapters to insure long life and durability in the most aggressive well conditions. External installation nipple makes installation easy.Rubber inner & outer casing gaskets for certified & approved water tight seal from ground water contamination. |
|
 | Cast iron well seal with rubber packing gland for submersible and jet pumps. Prevents contamination from surface drainage. Easy to install, just fit in casing and tighten bolts. Corrosion resistant zinc plated steel bolts. Painted finish. Split top |
|
 | Cast Aluminum standard ventilated
well cap with conduit opening. Standard 4". 5" and 6" cast aluminum well caps for use on steel or plastic casiing. Stainless steel set screws |
|
 | Submersible pump cable 12/4 (3-wire plus ground) UL listed 3 wire copper cable (with ground) for use within the well casing supplying power to the submersible pump. |
|
 | Strataflo bronze spring loaded check valve. For cold water service to retain liquid in a system preventing loss of prime when liquid source is lower than pump. It prevents backflow by allowing liquid to flow in one direction only. |
|
 | Pressure relief valve 1/2" heavy duty, no lead, bronze pressure relief valve for shallow, deep well and submersible pumps. Recommended only for cold water system installation. Spring loaded and pre-set at 100 PSI (Not adjustable). Not for use with hot water heaters. |
|
 | WellMate fiberglass bladder water pressure tanks are quicker, easier and less costly to install than steel tanks. They contain no steel, so there is no paint to scratch or touch-up and they cannot rust. All component materials are NSF and/or FDA listed. Factory 5 years warranty period for potable water residential installations and 2 years for non-residential installations.
|
|
 | Glycerine liquid filled 2" , 1/4" MNPT bottom connection, 2% accuracy, vacuum and pressure gauges with steel case and plastic lens for high vibration applications in 30 to 160 degrees Fahrenheit temperature.Use only with water |
|
 | The pressure switch starts and stops the pump motor automatically at a predetermined pressure. A tube connects the switch to some point in the system on the discharge side of the pump. The pressure in the system then acts directly on a diaphragm in the switch, which in turn actuates the contacts in the switch. |
|
 | Franklin Electric Motor 4", 3 wire, single phase, 60 Hz, 1/2 HP to 5 HP,water cooled, submersible water well motors with 48" Leads and control boxes. Single phase three-wire submersible motors require the use of control boxes. |
|
 | Franklin Monodrive variable speed constant pressure controllers are designed to provide constant pressure for single-phase, three-wire submersible water well pump systems. You can have constant pressure just by replacing the three-wire control box in a conventional system. |
|
 | PumpTec Automatic Protection Control For Franklin Submersible Motors, Single-phase, solid state, load monitoring devices designed specifically for Franklin submersible motors to protect from running dry. They protects the life of 4" submersible pump and reduces the odds of ever having to see the motor again |
|
 | The tape method was the only way to make a good splice until shrink tube splice kits became available. Many installers still use tape because it has worked for them for years. You crimp the conductors together, wrap each conductor with a layer of rubber tape followed with a layer of plastic electrical tape. This makes a watertight connection and insulates the conductors from each other and the well casing. Properly done, this technique makes an excellent splice, but is very time consuming. |
|
 | Intermatic 24 Hour Electric Sprinkler Timer. Rainproof enclosure with provision for rain sensor. Built-in pump start relay. On-off switch allows for shutdown during rainy days. 14 day skipper wheel permits watering to be omitted on selective days. |
|